Kisspeptin-10 Protocol Guide: Dosage & Reconstitution

Kisspeptin-10

Kisspeptin-10 is a peptide studied for its role in regulating the hypothalamic–pituitary–gonadal (HPG) axis. It stimulates natural hormone signaling by promoting the release of GnRH, which influences LH, FSH, and downstream testosterone or estrogen production.

How It Works

Kisspeptin → GnRH ↑ → LH/FSH ↑ → Natural Hormone Production ↑

Kisspeptin-10 acts upstream in the hormonal cascade by stimulating gonadotropin-releasing hormone (GnRH). This leads to increased luteinizing hormone (LH) and follicle-stimulating hormone (FSH), which support natural endocrine function and reproductive signaling.

Acts upstream of the HPG axis (not direct hormone replacement)

Stimulates natural GnRH release from the hypothalamus

Triggers LH and FSH production from the pituitary

Supports downstream testosterone or estrogen production

Kisspeptin Protocol Ranges

Standard Setup

Vial10 mg

Water3.0 mL bacteriostatic water

Concentration3.33 mg/mL

Conversion1 unit = 33.3 mcg

Standard Range

Dose100–300 mcg

Units3–9 units

Volume0.03–0.09 mL

Advanced Range

Dose300–500 mcg

Units9–15 units

Volume0.09–0.15 mL

Frequency1x daily or every other day

TimingMorning or pre-event

RouteSubcutaneous

Cycle Length4–8 weeks

Kisspeptin Protocol

10 mg vial → 3.0 mL BAC Water → 1 unit = 33.3 mcg

Weeks 1–2

Start / Sensitivity Phase

Dose100 mcg

Units3 units

Volume0.03 mL

Weeks 3–8

Build / Active Phase

Dose200 mcg

Units6 units

Volume0.06 mL

Optional Higher Range

Advanced Range

Dose300–500 mcg

Units9–15 units

Volume0.09–0.15 mL

Simple structure

Start lower to assess response, then build into a stable range. Higher doses are typically situational and not always necessary.

When & How to Use

Hormonal support protocols

Recovery from suppression

Libido or reproductive signaling support

Use in cycles rather than continuous use

Reconstitution & Dosing (10 mg Vial)

Vial10 mg

Water3.0 mL

Concentration3.33 mg/mL

Conversion1 unit = 33.3 mcg

Dose Reference

3 units ≈ 100 mcg

6 units ≈ 200 mcg

9 units ≈ 300 mcg

12 units ≈ 400 mcg

15 units ≈ 500 mcg

Reconstitution Steps

Draw 3.0 mL bacteriostatic water

Inject slowly into vial

Gently swirl (do not shake)

Allow full dissolution

Storage

Refrigerate at 2–8°C after reconstitution

Do not freeze after mixing

Use within 30 days

Storage & Shelf Life

Storage & Shelf Life

Lyophilized (Unmixed)

Refrigerated (2–8°C): ~12–24 months

Frozen (−20°C): up to ~2–3 years

Reconstituted (Mixed)

Refrigerated (2–8°C): ~30 days

Do not freeze after mixing

Avoid repeated temperature changes

Best Practice

Keep refrigerated, protect from light, and discard if the solution becomes cloudy, discolored, or develops particles.

Cycle Length & Timing Between Cycles

Active Cycle → Hormone Signaling Support → Break → Reassess

Standard Cycle

Cycle Length4–8 weeks

FrequencyDaily or every other day

Time Between Cycles

Break2–4 weeks off

GoalReassess hormone response

Simple Strategy

Kisspeptin is often used in shorter cycles to stimulate natural signaling. Time off helps evaluate whether endogenous hormone production is improving.

Monitoring During Use

Hormonal response

Libido changes

Energy and mood

Sleep patterns

Benefits

Supports natural hormone signaling

May increase LH and FSH production

Supports reproductive axis function

Often discussed for libido and endocrine support

Potential Side Effects

Flushing or warmth

Headache

Temporary fatigue

Hormonal fluctuations

Important Notes

Acts upstream (natural signaling vs direct hormone replacement)

Best used in cycles

Response varies based on baseline hormone levels

Monitor for hormonal changes

Important Disclaimer

Kisspeptin-10 is an investigational peptide and not FDA-approved. This content is for educational and research purposes only.

Kisspeptin-10 Guide → Peptide Directory →